大神们帮忙看看，这光猫还有救么？ – 无线路由器硬件改造以及故障维修 – 恩山WIFI论坛 – Powered by Discuz!

华为HG8245，不小心刷了俄罗斯固件后，管理页面192.168.100.1打开只有一个电信的LOID注册页面，无账号密码登陆界面，telnet连接，ROOT账号密码不是root admin ,无法登陆刷回其它固件，拆开接好TTL线后得到启动信息如下：

  3. U-Boot 1.1.4 (Dec  8 2011 – 14:02:37)

  5. U-Boot code: 90500000 -> 9051E6D0  BSS: -> 90554FB8

  6. RAM Configuration:

  7. Bank #0: 90000000 64 MB

  8. Flash: 16 MB

  9. *** Warning – bad CRC, using default environment

  11. In:    serial

  12. Out:   serial

  13. Err:   serial

  15. Extend LSW IS AR8316

  16. Initialize broadcast table … ok

  17. CPURTx Driver For Pilot <Board-A>!

  18. ### JFFS2 loading ‘fsok’ to 0x904bfe34

  19. Scanning JFFS2 FS: . done.

  20. ### JFFS2 load complete: 2 bytes loaded to 0x904bfe34

  21. No board type file!

  22. ui_board_id = 1

  23. [main.c__2899]::Magic1:0xf0bdbe7b, magic2 0x67fbf7ef, count -1426064529, flag -92291201, MainAreaOK -67175425, slaveAreaOK -419451010

  24. Start from normal system!

  25. Magic1:0x5a5a5a5a, magic2 0xa5a5a5a5, count 0, flag 0

  26. Addr[0]:0x0,Addr[1]:0x40000,Addr[2]:0x41000,Addr[3]:0x60000,Addr[4]:0x1e0000,Addr[5]:0xae0000,Addr[6]:0xe60000

  27. Start copy data from 0x201e0054 to 0x91000000 with sizeof 0x008ce040 …………………Done!

  28. Start system with ram disk and set bootcmd to

  29. BootArgs:noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,0x249024@0xc16fdc(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1

  30. Press d key to abort autoboot: 10

  31. ## Booting image at 20060054 …

  32.    Image Name:   Linux-2.6.21.7-hrt1

  33.    Image Type:   ARM Linux Kernel Image (uncompressed)

  34.    Data Size:    1484116 Bytes =  1.4 MB

  35.    Load Address: 90008000

  36.    Entry Point:  90008000

  37.    Loading Kernel Image … OK

  38. ## Loading Ramdisk Image at 91000000 …

  39.    Image Name:   squashfs

  40.    Image Type:   ARM Linux RAMDisk Image (uncompressed)

  41.    Data Size:    9232384 Bytes =  8.8 MB

  42.    Load Address: 00000000

  43.    Entry Point:  00000000

  45. Starting kernel …

  47. Uncompressing Linux………………………………………………………………………………… done, booting the kernel.

  48. Kernel Early-Debug on Level 0

  49. iotable information:

  50. virtual: 4093640704physical: 262144  length: 4096    type: 0

  51. virtual: 4145283072physical: 90432  length: 4096    type: 0

  52. virtual: 4145295360physical: 90435  length: 4096    type: 0

  53. virtual: 4145340416physical: 90446  length: 4096    type: 0

  54. virtual: 4145344512physical: 90447  length: 4096    type: 0

  55. virtual: 4093706240physical: 262160  length: 4096    type: 0

  56. virtual: 4093771776physical: 262176  length: 4096    type: 0

  57. virtual: 4145307648physical: 90438  length: 32768    type: 0

  58. virtual: 4145287168physical: 90433  length: 4096    type: 0

  59. virtual: 4145348608physical: 90448  length: 4096    type: 0

  60. virtual: 4076863488physical: 196608  length: 4096    type: 0

  61. virtual: 4145291264physical: 90434  length: 4096    type: 0

  62. virtual: 4145299456physical: 90436  length: 4096    type: 0

  63. virtual: 4145303552physical: 90437  length: 4096    type: 0

  64. hisilicon_map_io        281     [arch/arm/mach-sd5113_v100_p01/core.c]

  65. hisilicon_init_irq      108     [arch/arm/mach-sd5113_v100_p01/core.c]

  66. hisilicon_timer_init    228     [arch/arm/mach-sd5113_v100_p01/systimer.c]

  67. hi_kernel_wdt_init      216     [arch/arm/mach-sd5113_v100_p01/hi_drv_wdt.c]

  68. hisilicon_init_machine  175     [arch/arm/mach-sd5113_v100_p01/core.c]

  69. hi_kernel_pci_preinit   390     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]

  70. pci clock is on!

  71. hi_kernel_pci_postinit  488     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]

  72. hi_kernel_pci_postinit on!

  73. hi_kernel_pci_map_irq   367     [arch/arm/mach-sd5113_v100_p01/hi_pci.c]

  74. Linux version 2.6.21.7-hrt1 (huangchongjun@suse-ssmp-server) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #2 Tue Jul 5 16:00:47 HKT 2011

  75. CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f

  76. Machine: SD5113-V100-PILOT-B01

  77. Memory policy: ECC disabled, Data cache writeback

  78. Get mem size 0x3200000;

  79. CPU0: D VIPT write-back cache

  80. CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

  81. CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

  82. Built 1 zonelists.  Total pages: 12700

  83. Kernel command line: noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,0x249024@0xc16fdc(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1

  84. PID hash table entries: 256 (order: 8, 1024 bytes)

  85. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

  86. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

  87. Memory: 50MB = 50MB total

  88. Memory: 38588KB available (2676K code, 233K data, 108K init)

  89. Security Framework v1.0.0 initialized

  90. Capability LSM initialized

  91. Mount-cache hash table entries: 512

  92. CPU: Testing write buffer coherency: ok

  93. NET: Registered protocol family 16

  94. Hisilicon clock system V0.01

  95. [clk_register, 244]     AHBCLK

  96. [clk_register, 244]     ARMCORECLK

  97. [clk_register, 244]     UARTCLK

  98. PCI: device 0000:00:03.0 has unknown header type 1c, ignoring.

  99. PCI: device 0000:00:04.0 has unknown header type 1c, ignoring.

  100. PCI: device 0000:00:05.0 has unknown header type 1c, ignoring.

  101. PCI: device 0000:00:06.0 has unknown header type 1c, ignoring.

  102. PCI: device 0000:00:07.0 has unknown header type 1c, ignoring.

  103. PCI: device 0000:00:08.0 has unknown header type 1c, ignoring.

  104. PCI: device 0000:00:09.0 has unknown header type 1c, ignoring.

  105. PCI: device 0000:00:0a.0 has unknown header type 1c, ignoring.

  106. PCI: device 0000:00:0b.0 has unknown header type 1c, ignoring.

  107. PCI: device 0000:00:0c.0 has unknown header type 1c, ignoring.

  108. PCI: device 0000:00:0d.0 has unknown header type 1c, ignoring.

  109. PCI: device 0000:00:0e.0 has unknown header type 1c, ignoring.

  110. PCI: device 0000:00:0f.0 has unknown header type 1c, ignoring.

  111. PCI: device 0000:00:10.0 has unknown header type 1c, ignoring.

  112. PCI: device 0000:00:11.0 has unknown header type 1c, ignoring.

  113. PCI: device 0000:00:12.0 has unknown header type 1c, ignoring.

  114. PCI: device 0000:00:13.0 has unknown header type 1c, ignoring.

  115. PCI: device 0000:00:14.0 has unknown header type 1c, ignoring.

  116. PCI: device 0000:00:15.0 has unknown header type 1c, ignoring.

  117. PCI: device 0000:00:16.0 has unknown header type 1c, ignoring.

  118. PCI: device 0000:00:17.0 has unknown header type 1c, ignoring.

  119. PCI: device 0000:00:18.0 has unknown header type 1c, ignoring.

  120. PCI: device 0000:00:19.0 has unknown header type 1c, ignoring.

  121. PCI: device 0000:00:1a.0 has unknown header type 1c, ignoring.

  122. PCI: device 0000:00:1b.0 has unknown header type 1c, ignoring.

  123. PCI: device 0000:00:1c.0 has unknown header type 1c, ignoring.

  124. PCI: device 0000:00:1d.0 has unknown header type 1c, ignoring.

  125. PCI: device 0000:00:1e.0 has unknown header type 1c, ignoring.

  126. PCI: device 0000:00:1f.0 has unknown header type 1c, ignoring.

  127. PCI: bus0: Fast back to back transfers enabled

  128. istatus and imask 16777216

  129. istatus and imask 0

  130. map irq: slot 0, pin 1, devslot 2, irq: 21

  131. usbcore: registered new interface driver usbfs

  132. usbcore: registered new interface driver hub

  133. usbcore: registered new device driver usb

  134. NET: Registered protocol family 2

  135. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

  136. TCP established hash table entries: 2048 (order: 2, 16384 bytes)

  137. TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

  138. TCP: Hash tables configured (established 2048 bind 2048)

  139. TCP reno registered

  140. checking if image is initramfs…it isn’t (bad gzip magic numbers); looks like an initrd

  141. Freeing initrd memory: 9016K

  142. Registering GDB sysrq handler

  143. squashfs: version 3.4 (2008/08/26) Phillip Lougher

  144. squashfs: LZMA suppport for slax.org by jro

  145. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.

  146. io scheduler noop registered

  147. io scheduler anticipatory registered

  148. io scheduler deadline registered

  149. io scheduler cfq registered (default)

  150. Serial: dw  uart driver

  151. dev:f2: ttyAMA0 at MMIO map 0x1614f000 mem 0xf714f000 (irq = 17) is a AMBA/DW

  152. dev:f1: ttyAMA1 at MMIO map 0x1614e000 mem 0xf714e000 (irq = 16) is a AMBA/DW

  153. RAMDISK driver initialized: 4 RAM disks of 23000K size 1024 blocksize

  154. PPP generic driver version 2.4.2

  155. PPP Deflate Compression module registered

  156. PPP BSD Compression module registered

  157. PPP MPPE Compression module registered

  158. NET: Registered protocol family 24

  159. SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).

  160. CSLIP: code copyright 1989 Regents of the University of California.

  161. SLIP linefill/keepalive option.

  162. netconsole: not configured, aborting

  163. Start to set chip MaxBufWriteSize.

  164. !Not find NUMONYX JS28F128M29EWHA chip.

  165. hisilicon: Found 1 x16 devices at 0x0 in 16-bit bank

  166. Amd/Fujitsu Extended Query Table at 0x0040

  167. hisilicon: CFI does not contain boot bank location. Assuming top.

  168. number of CFI chips: 1

  169. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

  170. Hisilicon flash: registering whole flash at once as master MTD

  171. 8 cmdlinepart partitions found on MTD device hisilicon

  172. Creating 8 MTD partitions on “hisilicon”:

  173. 0x00000000-0x00040000 : “boot”

  174. 0x00040000-0x00041000 : “flashcfg”

  175. 0x00041000-0x00060000 : “syspara”

  176. 0x00060000-0x001e0000 : “krnl”

  177. 0x001e0054-0x00ae0000 : “rootfs”

  178. 0x00c16fdc-0x00e60000 : “minisystem”

  179. 0x00e60000-0x00fe0000 : “jffs2cfg”

  180. 0x00fe0000-0x01000000 : “reserved”

  181. usb clock is on!

  182. h2v100-ehci h2v100-ehci.0: h2v100-ehci

  183. h2v100-ehci h2v100-ehci.0: new USB bus registered, assigned bus number 1

  184. h2v100-ehci h2v100-ehci.0: irq 23, io mem 0x40010000

  185. h2v100-ehci h2v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004

  186. usb usb1: configuration #1 chosen from 1 choice

  187. hub 1-0:1.0: USB hub found

  188. hub 1-0:1.0: 2 ports detected

  189. h2v100-ohci h2v100-ohci.0: h2v100-ohci

  190. h2v100-ohci h2v100-ohci.0: new USB bus registered, assigned bus number 2

  191. h2v100-ohci h2v100-ohci.0: irq 24, io mem 0x40020000

  192. usb usb2: configuration #1 chosen from 1 choice

  193. hub 2-0:1.0: USB hub found

  194. hub 2-0:1.0: 2 ports detected

  195. Netfilter messages via NETLINK v0.30.

  196. ip_tables: (C) 2000-2006 Netfilter Core Team

  197. arp_tables: (C) 2002 David S. Miller

  198. TCP cubic registered

  199. NET: Registered protocol family 1

  200. NET: Registered protocol family 17

  201. ieee80211: 802.11 data/management/control stack, git-1.1.13

  202. ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>

  203. RAMDISK: squashfs filesystem found at block 0, block number 9015

  204. RAMDISK: Loading 9015KiB [1 disk] into ram disk… done.

  205. VFS: Mounted root (squashfs filesystem) readonly.

  206. Freeing init memory: 108K

  208.                         -=#  DOPRA LINUX 1.0  #=-

  209.                         -=#  EchoLife WAP 0.1  #=-

  210.                         -=#  Huawei Technologies Co., Ltd #=-

  212. mount file system

  213. Loading the kernel modules:

  214. Loading module: nf_conntrack

  216.   nf_conntrack_init new nf_conntrack version 0.5.0 (400 buckets, 3200 max)

  217. Loading module: nf_conntrack_ftp

  218. Loading module: nf_conntrack_tftp

  219. Loading module: nf_nat

  220. Loading module: nf_nat_ftp

  221. Loading module: nf_nat_tftp

  222. Making device instances:

  223. Setting console log message level:

  224. Setting hostname:

  225. Settingup the sysctl configurations:

  226. Setting up interface lo:

  227. Running local startup scripts.

  229. *******************************************

  230. –==      Welcome To EchoLife WAP      ==–

  231. –==   Huawei Technologies Co., Ltd.   ==–

  232. *******************************************

  233. WAP Ver:V100R003C00SPC106B176

  234. WAP Timestamp:2012/02/26 12:15:22

  235. *******************************************

  237. Start lunch kmsgread …

  238. Pid of kmsgrread is:

  239. Rootfs time stamp:2012-02-26_12:20:32

  240. Mount the JFFS2 file system:

  241. SCSI subsystem initialized

  242. Initializing USB Mass Storage driver…

  243. usbcore: registered new interface driver usb-storage

  244. USB Mass Storage support registered.

  245. fuse init (API version 7.8)

  246. User init start……

  247. Loading the SD5113V100 modules:

  248. ETH install success!

  249. request_irq hi_dp!!!!

  251. SD511X  DP  V1.0 is installed !

  253. SD511x IOCTL_DP  V1.0 is installed

  255. SD511x MDIO ID V1.0 is installed

  257. SD511x GPIO VERSION 1.0 is installed

  259. SD511x GPIO_INT ID 1.0 is installed

  261. SD511x I2C ID V1.0 is installed

  263. SD511x TIMER ID V1.0 is installed

  265. SD511X SPI ID v1.0 is installed

  267. SD511X  SYSCTL  V1.0 is installed

  269. SD511x UART ID V1.0 is installed

  271. SD5113 DMA ID V1.0 is installed

  272. <6>

  273. SD511X HW  ID v1.0 is installed

  275. SD511x EXT_INT ID 1.0 is installed

  277. SD511x IOCTL_SYSCTL  V1.0 is installed

  278. ifconfig eth0 hw ether 7C:60:97:89:F4:A5

  279. <6>device eth0 entered promiscuous mode

  280. br0: port 1(eth0) entering learning state

  281. Loading the EchoLife WAP modules: LDSP

  282. SSP For LDSP Install Successfully…

  283. HLP For LDSP Install Successfully…

  284. CHIPADP-PHY For LDSP Install Successfully…

  285. Get version through hardware!

  286. CHIPADP-SD5113 For LDSP Install Successfully…

  287. GPIO For LDSP Install Successfully…

  288. HIGHWAY For LDSP Install Successfully…

  289. I2C For LDSP Install Successfully…

  290. MDIO For LDSP Install Successfully…

  291. CHIPADP-AR8316 LSW For LDSP Install Successfully…

  292. SPI For LDSP Install Successfully…

  293. UART For LDSP Install Successfully…

  294. BATTERY For LDSP Install Successfully…

  295. PLOAM For LDSP Install Successfully…

  296. GMAC For LDSP Install Successfully…

  297. KEY For LDSP Install Successfully…

  298. LSW For LDSP Install Successfully…

  299. LED For LDSP Install Successfully…

  300. OPTIC For LDSP Install Successfully…

  301. RF For LDSP Install Successfully…

  302. le88226 For LDSP install successfully…

  303. DEV For LDSP Install Successfully…

  304. USB For LDSP Install Successfully…

  305. HW_KER_BBSP_COMMON_HLE_SET_DEBUG_E:13Common HLP For BBSP Install Successfully…

  306. topo For BBSP Install Successfully…

  307. FLOW For BBSP Install Successfully…

  308. VETH For LDSP Install Successfully…

  309. hw_pkt_tunnel Install Successfully…

  310. WIFI For BBSP Install Successfully…

  311. Dosflt For BBSP Install Successfully…

  312. EMAC For LDSP Install Successfully…

  313. MPCP For LDSP Install Successfully…

  314. Loading DSP temporary modules:

  315. linux kernel dopra is installed!

  317. dsp sdk  insmod success!

  318. DSP For LDSP Install Successfully…

  319. Loading the EchoLife WAP modules: BBSP

  320. ipv6 Install Successfully…

  321. hw_acl init success

  322. hw_acl_cmd_init OK!

  323. hw_dhcp Install Successfully…

  324. napt register conntrack_handler

  325. NAPT For BBSP Install Successfully…

  326. hw_igmp_kernel Install Successfully…

  328. _init_session SUCCESS

  329. table_size =3040 hash_size = 380

  330. ffwd register conntrack_handler

  331. hw_ker_ffwd_core  install

  332. hw_ker_ffwd_ipv4  install

  333. CODEC For LDSP Install Successfully…

  334. hw_ringchk_kernel Install Successfully…

  335. hw_ethoam_kernel Install Successfully…

  336. hw_pppoe Install Successfully…

  337. Portal For BBSP Install Successfully…

  339. install success

  340. hw_bind_init…

  341. KARP Install Successfully…

  342. ssmp bbsp vspa igmp amp apm clid&

  343. Start ldsp_user…0

  344. Start start pid=516; uiProcNum=7;

  346. <LDSP>Ldsp cfg start at 12, Line: 803  

  347. HW_LdspCfg_XponProc uiPonAbility = 2

  348. <LDSP>HW_LdspCfg_XponProc start from gpon, uiUpMode=1.

  349. <LDSP cfg>Set uiUpMode=1.

  350. <LDSP>Hardware board id is 1 !

  351. <LDSP>Hardware pcb id is 3 !

  352. SD5113 test self OK

  353. Lsw test self OK

  354. Optic vendor_pn LTB3468L-CCG+  

  355. Optic input vendor_pn LTB3468L-CCG+

  356. Optic calMode 0

  357. GPON opened success !

  358. 1

  359. usb1 gpio clock open

  361. <LDSP>Ldsp cfg  end at 13, Line: 847  

  362. HW_LdspUser_XponProc uiPonAbility = 2

  363. <LDSP>HW_LdspUser_XponProc start from gpon, uiUpMode=1.

  364. <LDSP User>Set uiUpMode=1.

  365. <LDSP>HW_LdspUser_NetLink_Init initial success.

  366. <LDSP>HW_LdspUser_InitNetlink initial success.

  367. hw_quickcfg_resume.c <74>     uiRet=0x00000000 arg=0x00000000

  369. system not enable the restore flag!

  370. Start VSPA …InitFrame get next state amp; PID=541; state=0; Sec=15;

  371. InitFrame get next state amp; PID=541; state=0; Sec=15;

  372. InitFrame get next state igmp; PID=542; state=0; Sec=15;

  373. InitFrame get next state igmp; PID=542; state=0; Sec=15;

  374. InitFrame get next state apm; PID=552; state=0; Sec=15;

  375. InitFrame get next state apm; PID=552; state=0; Sec=15;

  376. InitFrame get next state ssmp; PID=539; state=0; Sec=15;

  377. InitFrame get next state ssmp; PID=539; state=0; Sec=15;

  378. HW_DIA_InitHmem success;

  379. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  380. HW_DIA_InitHmem success;

  381. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  382. InitFrame get next state clid; PID=553; state=0; Sec=16;

  383. InitFrame get next state clid; PID=553; state=0; Sec=16;

  384. HW_DIA_InitHmem success;

  385.   PID  Uid     VmSize Stat Command

  386. HW_DIA_InitHmem success;

  387. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  388. HW_DIA_InitHmem success;

  389. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  391. [HMEM]Start Times uiStartNum = 0x0.

  393. [HMEM]HMEM initial success.

  394. InitFrame get next state bbsp; PID=540; state=0; Sec=16;

  395. InitFrame get next state bbsp; PID=540; state=0; Sec=16;

  396. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  397.     1 root        608 S   init      

  398.     2 root            SWN [ksoftirqd/0]

  399.     3 root            SW  [watchdog/0]

  400.     4 root            SW< [events/0]

  401.     5 root            SW< [khelper]

  402.     6 root            SW< [kthread]

  403.    30 root            SW< [kblockd/0]

  404.    33 root            SW< [khubd]

  405.    47 root            SW  [pdflush]

  406.    48 root            SW  [pdflush]

  407.    49 root            SW< [kswapd0]

  408.    50 root            SW< [aio/0]

  409.    65 root            SW  [mtdblockd]

  410.   113 root        256 S   init      

  411.   114 root        572 S   /bin/sh /etc/rc.d/rc.sysinit

  412.   191 root            DW< [wap_lastword]

  413.   192 root            DW< [wap_ktrace]

  414.   196 root        580 S   kmsgread

  415.   203 root        600 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start

  416.   218 root            SWN [jffs2_gcd_mtd7]

  417.   456 root            SW  [mpcp]

  418.   465 root            SW< [kTimerTask]

  419.   490 root            SW  [cpucar]

  420.   516 root        628 S   start ssmp bbsp vspa igmp amp apm clid

  421.   536 root        844 S   hw_ldsp_user

  423. HW_XML_DBMain HW_XML_DBConfFileInit OK

  424. WAP Loaded Custom Configuration <Msg>: 0x00000000;

  425. ProcMax=30          ModuleMax=20      

  426. GroupMax=2          TraceMax=8      

  427. StatMax=16          MqLenMax=4096   

  428. uiMqNumMax=1024            

  429. HW_DIA_InitHmem success;

  430. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  431.   539 root       1340 R   ssmp

  432.   540 root       1312 R   bbsp

  433.   541 root        964 R   amp

  434.   542 root       1108 R   igmp

  435.   549 root        560 S   /bin/sh /bin/watchproc.sh vspa_sip

  436.   551 root        824 S   smp_usb

  437.   552 root        868 R N apm

  438.   553 root        792 R   clid

  439.   554 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start

  440.   555 root        380 S   sleep 30

  441.   556 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start

  442.   557 root       1264 R N vspa_sip

  443.   558 root        380 S   sleep 60

  444.   562 root        380 S   sleep 30

  445.   563 root        240 S   /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start

  446.   564 root        380 S   sleep 40

  447.   565 root        604 R   ps

  450. BusyBox v1.4.1 (2011-07-29 10:25:20 HKT) Built-in shell (ash)

  451. Enter ‘help’ for a list of built-in commands.

  453. VSPA pri from 0 to 10

  454. InitFrame get next state vspa_sip; PID=557; state=0; Sec=16;

  455. InitFrame get next state vspa_sip; PID=557; state=0; Sec=16;

  456. Read line cwmp cwmp 1

  457. ;

  458. Load auto start conig:0 cwmp cwmp 1

  459. Read line ethoam ethoam 1

  460. ;

  461. Load auto start conig:1 ethoam ethoam 1

  462. WAP Loaded Custom Configuration <Db>: 0x00000000;

  463. uiEnable=1            MsgWaitTime=10000   

  464. WAP(Dopra Linux) # HW_DIA_InitHmem success;

  465. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  466. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg

  467. Read DB Failure,uiFlag = 2

  468. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg

  469. Read DB Failure,uiFlag = 3

  470. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg.FilMid.1

  471. Read DB Failure,uiFlag = 4

  472. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg

  473. Read DB Failure,uiFlag = 5

  474. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg.SaveInterval.1

  475. Read DB Failure,uiFlag = 6

  476. [hw_xml_dbmain.c]:[3741]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_LogCfg

  477. Read DB Failure,uiFlag = 1

  478. WAP Load Custom Configuration: uiRet=0x00000000;

  479. TimeForRebootSys=1      TimeForResetCfg=10      

  480. WAP Loaded Custom Configuration <WebServer>: 0xf7109009

  481. Enable=1                MaxConNumPerSec=1000   

  482. MaxConNumTotal=128      MaxPwdLength=128     

  483. MaxNameLength=32        PortNum=80      

  484. Default Language=chinese

  485. Web custom config loaded ……

  486. HW_WEB_RegCgiCmd:uiError=0x00000000;

  487. HW_WEB_RegAspCmd:uiError=0x00000000;

  488. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1

  489. WAP Loaded Custom Configuration <Swm>: 0x00000000;

  490. BufferSize=1048576      MaxItemNum=16      

  491. MaxChnl=8               MaxDev=8        

  492. FlashCfgAddr=0x00040000 FlashCfgLen=4096   

  493. PackMarkV1=HWTP         PackMarkV2=HWNP;

  494. BootCountAddr=0x933ff000

  495. WAP Loaded Custom Configuration <CFG>: 0x00000000;

  496. CfgCallWaitTime=100000  

  497. WAP Loaded Custom Configuration <CFM>: 0x00000000;

  498. Enable=1                MaxObjNum=64      

  499. CFM start!AppName:ssmp

  501. ssmp CFM Used 166 ms

  502. CFM end!AppName:ssmp,uiRet=0x0

  503. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  504. HW_Init_ModuleSsp HW_IP_LOAD_CONFIG END

  506. [Start Phase]::uiStartPhase: 0, uiEndPhase: 1, Seconds: 6

  507. InitFrame get next state ssmp; PID=539; state=1; Sec=18;

  508. InitFrame get next state bbsp; PID=540; state=1; Sec=18;

  509. InitFrame get next state amp; PID=541; state=1; Sec=18;

  510. InitFrame get next state igmp; PID=542; state=1; Sec=18;

  511. InitFrame get next state clid; PID=553; state=1; Sec=18;

  512. InitFrame get next state vspa_sip; PID=557; state=1; Sec=18;

  513. InitFrame get next state apm; PID=552; state=1; Sec=18;

  514. WAP Loaded Custom Configuration <Apm>: 0x00000000;

  515. BatteryChangeTime=300      uiBootDelay=600      

  516. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.X_HW_LANBIND

  517. WAP Loaded Custom Configuration <CLI>: 0x00000000;

  518. Enable=1                UserNameLen=32      

  519. UserPwdLen=64           WelcomeInfo:Welcome Visiting Huawei Home Gateway

  520. Copyright by Huawei Technologies Co., Ltd.

  521. MaxTelnetNum=4          HistoryNum=20      

  522. TelnetPortId=23         Prompt:WAP     

  523. hw_apm_init.c:<262>:APM get board id=1;

  524. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.1.X_HW_LANBIND

  525. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANIPConnection.1.X_HW_LANBIND

  526. HW_APM_ModuleInit SUCCESS!

  527. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1.X_HW_LANBIND

  528. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.3.WANIPConnection.1.X_HW_LANBIND

  529. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.3.WANPPPConnection.1.X_HW_LANBIND

  530. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.4.WANIPConnection.1.X_HW_LANBIND

  531. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.4.WANPPPConnection.1.X_HW_LANBIND

  532. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.5.WANIPConnection.1.X_HW_LANBIND

  533. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.5.WANPPPConnection.1.X_HW_LANBIND

  534. Kmsgread (196) exit.

  535. Send exit message to old kmsgread 196;

  536. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.6.WANIPConnection.1.X_Set kmsgread process pid to:553;

  537. HW_LANBIND

  538. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.6.WANPPPConnection.1.X_HW_LANBIND

  539. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.7.WANIPConnection.1.X_HW_LANBIND

  540. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.7.WANPPPConnection.1.X_HW_LANBIND

  541. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.8.WANIPConnection.1.X_HW_LANBIND

  542. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.8.WANPPPConnection.1.X_HW_LANBIND

  544. [Start Phase]::uiStartPhase: 1, uiEndPhase: 2, Seconds: 2

  545. InitFrame get next state ssmp; PID=539; state=2; Sec=20;

  546. InitFrame get next state amp; PID=541; state=2; Sec=20;

  547. InitFrame get next state igmp; PID=542; state=2; Sec=20;

  548. HW_Init_Frame CLI Successful.

  549. InitFrame get next state bbsp; PID=540; state=2; Sec=20;

  550. InitFrame get next state vspa_sip; PID=557; state=2; Sec=20;

  551. <APM>HW_Shell_ApmCmdProcInit OK

  552. HW_Init_Frame APM Successful.

  553. <CFM>uiMsgMid = 0x4c

  554. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_VendorInfo

  555. CFM start!AppName:apm

  556. HW_ONT_GetAccessMode : uiPonModeInd:[0]

  557. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AmpInfo.X_HW_Spec

  558. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AmpInfo.X_HW_Spec.X_HW_EthSpec.1

  560. apm CFM Used 142 ms

  561. CFM end!AppName:apm,uiRet=0x0

  562. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AmpInfo.X_HW_Spec.X_HW_EthSpec.2

  563. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AmpInfo.X_HW_Spec.X_HW_EthSpec.3

  564. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AmpInfo.X_HW_Spec.X_HW_EthSpec.4

  565. [AMP]: HW_AMP_InitHGDetect() Error! Return=-149905368;

  566. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_AMPConfig.PortIsolate

  568. GetSwitchFromTree Failed! [4145061928] [disable]

  569. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_CATVConfiguration

  570. [AMP]: Get CATV Enable from Tree Error! Return=-149905368;

  572. [Start Phase]::uiStartPhase: 2, uiEndPhase: 3, Seconds: 0

  573. InitFrame get next state ssmp; PID=539; state=3; Sec=20;

  574. InitFrame get next state igmp; PID=542; state=3; Sec=20;

  575. IGMP Init Lsw lib Tbl Successfully!

  576. InitFrame get next state bbsp; PID=540; state=3; Sec=20;

  577. InitFrame get next state vspa_sip; PID=557; state=3; Sec=20;

  578. InitFrame get next state amp; PID=541; state=3; Sec=20;

  579. <CFM>uiMsgMid = 0x60

  580. CFM start!AppName:amp

  581. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_VendorInfo

  583. amp CFM Used 78 ms

  584. CFM end!AppName:amp,uiRet=0x0

  585. HW_IGMP_GetVendorInfo Failed! uiRet is 4145061928

  586. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_FeatureList.BBSPCustomization

  587. HW_IGMP_GetMulticastToUnicastInfo Failed! uiRet is 4145061928

  588. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1

  589. [IFM_ERROR],file:hw_ifm_main.c,line:174:IFM_IPIF_Init error:0xf710a028

  590. device br0 already exists; can’t create bridge with the same name

  591. device eth0 is already a member of a bridge; can’t enslave it to bridge br0.

  592. ifconfig: SIOCSIFADDR: Invalid argument

  593. ifconfig: SIOCSIFADDR: Invalid argument

  595. HW_IFM_UpdateWANCONN: wan connection instance number is 0

  596. [IFM_INFO],file:hw_wan_vlanswitch.c,line:1231:tag0 supported:0, vlanpri supported:0, wannum supported:2

  597. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_FeatureList.BBSPCustomization.RingCheck

  599. [Start Phase]::uiStartPhase: 3, uiEndPhase: 4, Seconds: 0

  600. InitFrame get next state bbsp; PID=540; state=4; Sec=20;

  601. InitFrame get next state amp; PID=541; state=4; Sec=20;

  602. InitFrame get next state ssmp; PID=539; state=4; Sec=20;

  603. InitFrame get next state igmp; PID=542; state=4; Sec=20;

  604. InitFrame get next state vspa_sip; PID=557; state=4; Sec=20;

  605. HW_SSP_RegIfmEvt success

  606. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_DHCPSLVSERVER

  607. insmod: cannot insert ‘/lib/modules/2.6.21.7-hrt1/kernel/net/netfilter/nf_conntrack_ftp.ko’: File exists (-1): File exists

  608. insmod: cannot insert ‘/lib/modules/2.6.21.7-hrt1/kernel/net/ipv4/netfilter/nf_nat_ftp.ko’: File exists (-1): File exists

  609. insmod: cannot insert ‘/lib/modules/2.6.21.7-hrt1/kernel/net/netfilter/nf_conntrack_tftp.ko’: File exists (-1): File exists

  610. insmod: cannot insert ‘/lib/modules/2.6.21.7-hrt1/kernel/net/ipv4/netfilter/nf_nat_tftp.ko’: File exists (-1): File exists

  611. port #0: 5060

  612. port #0: 5060

  613. port #1: 5061

  614. port #1: 5061

  615. port #2: 5062

  616. port #2: 5062

  617. port #3: 5063

  618. port #3: 5063

  619. port #4: 5064

  620. port #4: 5064

  621. port #5: 5065

  622. port #5: 5065

  623. port #6: 5066

  624. port #6: 5066

  625. port #7: 5067

  626. port #7: 5067

  628. new module

  629. —register conntrack sip alg ko succeed!

  631. nf_nat_sip init success—HW_LSW_GPON_CfgReset is called.

  632. @@@HW_LSW_ADPT_SetGponMapMode uiNewGlbMapMode: 1  oldGlbMapMode: 1

  633. nf_conntrack_rtsp v0.6.21 loading

  634. HW_DIA_InitHmem success;

  635. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  636. Init OMCI HW_DIA_InitResource 0x0

  637. ldsp return the result:0

  638. Get the Los Status:1

  639. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_OmciInfo.OmciVersion

  640. ======gpon optic monitor start=====

  641. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_VendorInfo

  643. =====get wan vlan tde version fail!!!======

  644. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_OmciInfo.DbaType

  645. [OMCI_TAPI_GetSRIndication]Invalid recode [0xf710a028]

  646. [OMCI]: Get SR Indication error! Return code = 0xf710a028!

  647. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_VendorInfo

  648. [OMCI]: Get VendorID From XML  err:0xf710a028

  649. [OMCI]: Check led status failed!

  650. Init OMCI HW_Shell_Init 0x0

  652. No server avilable!

  653. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_FeatureList.BBSPCustomization

  655. [Start Phase]::uiStartPhase: 4, uiEndPhase: 5, Seconds: 2

  656. InitFrame get next state amp; PID=541; state=5; Sec=22;

  657. InitFrame get next state ssmp; PID=539; state=5; Sec=22;

  658. InitFrame get next state igmp; PID=542; state=5; Sec=22;

  659. InitFrame get next state vspa_sip; PID=557; state=5; Sec=22;

  660. InitFrame get next state bbsp; PID=540; state=5; Sec=22;

  661. <CFM>uiMsgMid = 0x92

  662. CFM start!AppName:igmp

  664. [Start Phase]::uiStartPhase: 5, uiEndPhase: 6, Seconds: 0

  665. InitFrame get next state amp; PID=541; state=6; Sec=22;

  666. InitFrame get next state ssmp; PID=539; state=6; Sec=22;

  667. InitFrame get next state bbsp; PID=540; state=6; Sec=22;

  668. InitFrame get next state vspa_sip; PID=557; state=6; Sec=22;

  669. OpticPN = LTB3468L-CCG+    Type = 2

  670. Init Access Mode To GPON ……………..

  671. [Start Phase]::uiStartPhase: 6, uiEndPhase: 7, Seconds: 0

  672. ======gpon optic monitor stop=====

  673. InitFrame get next state amp; PID=541; state=7; Sec=22;

  674. InitFrame get next state ssmp; PID=539; state=7; Sec=22;

  675. InitFrame get next state bbsp; PID=540; state=7; Sec=22;

  676. [PLOAM]ONUID(0): O1 => O1

  678. igmp CFM Used 142 ms

  679. CFM end!AppName:igmp,uiRet=0x0

  680. InitFrame get next state vspa_sip; PID=557; state=7; Sec=22;

  681. br0: topology change detected, propagating

  682. br0: port 1(eth0) entering forwarding state

  683. ath_hal: 0.9.17.1 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2316, RF2317, WRITE_EEPROM, 11D)

  684. ath_dfs: Version 2.0.0

  685. Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved

  686. wlan: 0.8.4.2 (Atheros/multi-bss)

  687. ath_rate_atheros: Version 2.0.1

  688. Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved

  689. ath_pci: 0.9.4.5 (Atheros/multi-bss)

  690. ath_pci: CR-LSDK-1.4.0.112

  691. PCI: enabling device 0000:00:02.0 (0340 -> 0342)

  692. WIFI MAC[0]:0x7c

  693. WIFI MAC[1]:0x60

  694. WIFI MAC[2]:0x97

  695. WIFI MAC[3]:0x89

  696. WIFI MAC[4]:0xf4

  697. WIFI MAC[5]:0xa9

  698. WIFI test self OK

  699. Chan  Freq  RegPwr  HT   CTL CTL_U CTL_L DFS

  700.    1  2412n     20  HT20  1    0    0     N

  701.    1  2412n     20  HT40  1    0    1     N

  702.    2  2417n     20  HT40  1    0    1     N

  703.    2  2417n     20  HT20  1    0    0     N

  704.    3  2422n     20  HT20  1    0    0     N

  705.    3  2422n     20  HT40  1    0    1     N

  706.    4  2427n     20  HT40  1    0    1     N

  707.    4  2427n     20  HT20  1    0    0     N

  708.    5  2432n     20  HT40  1    1    0     N

  709.    5  2432n     20  HT40  1    0    1     N

  710.    5  2432n     20  HT20  1    0    0     N

  711.    6  2437n     20  HT40  1    1    0     N

  712.    6  2437n     20  HT40  1    0    1     N

  713.    6  2437n     20  HT20  1    0    0     N

  714.    7  2442n     20  HT40  1    0    1     N

  715.    7  2442n     20  HT20  1    0    0     N

  716.    7  2442n     20  HT40  1    1    0     N

  717.    8  2447n     20  HT40  1    1    0     N

  718.    8  2447n     20  HT40  1    0    1     N

  719.    8  2447n     20  HT20  1    0    0     N

  720.    9  2452n     20  HT40  1    1    0     N

  721.    9  2452n     20  HT40  1    0    1     N

  722.    9  2452n     20  HT20  1    0    0     N

  723.   10  2457n     20  HT40  1    1    0     N

  724.   10  2457n     20  HT20  1    0    0     N

  725.   11  2462n     20  HT40  1    1    0     N

  726.   11  2462n     20  HT20  1    0    0     N

  727.   12  2467n     20  HT40  1    1    0     N

  728.   12  2467n     20  HT20  1    0    0     N

  729.   13  2472n     20  HT40  1    1    0     N

  730.   13  2472n     20  HT20  1    0    0     N

  731. [WIFI]Channel list OK.

  732. dfs_init_radar_filters: Unknown dfs domain 0

  733. wifi0: 11nght20 rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps

  734. wifi0: 11nght20 MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15

  735. wifi0: 11nght40plus rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps

  736. wifi0: 11nght40plus MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15

  737. wifi0: 11nght40minus rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps

  738. wifi0: 11nght40minus MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15

  739. wifi0: mac 384.2 phy 15.15 radio 12.0

  740. wifi0: Use hw queue 1 for WME_AC_BE traffic

  741. wifi0: Use hw queue 0 for WME_AC_BK traffic

  742. wifi0: Use hw queue 2 for WME_AC_VI traffic

  743. wifi0: Use hw queue 3 for WME_AC_VO traffic

  744. wifi0: Use hw queue 8 for CAB traffic

  745. wifi0: Use hw queue 9 for beacons

  746. wifi0: Use hw queue 7 for UAPSD

  747. wifi0: Atheros 9280: mem=0x38000000, irq=21 hw_base=0xc3cc0000

  748. wlan: mac acl policy registered

  749. Error for wireless request “Set Tx Power” (8B26) :

  750.     SET failed on device ath0 ; No such device.

  751. Error for wireless request “Set Tx Power” (8B26) :

  752.     SET failed on device ath0 ; No such device.

  753. WLAN init fail!

  755. [Start Phase]::uiStartPhase: 7, uiEndPhase: 8, Seconds: 12

  756. InitFrame get next state bbsp; PID=540; state=8; Sec=34;

  757. <CFM>uiMsgMid = 0x80

  758. InitFrame get next state ssmp; PID=539; state=8; Sec=34;

  759. HW_Init_Frame Amp Successful.

  760. InitFrame get next state vspa_sip; PID=557; state=8; Sec=34;

  761. CFM start!AppName:bbsp

  763. bbsp CFM Used 4457 ms

  764. CFM end!AppName:bbsp,uiRet=0x0

  765. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_FeatureList.BBSPCustomization

  766. [hw_xml_dbmain.c]:[3510]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.X_HW_FeatureList.BBSPCustomization

  768. Init DSP starting…

  769. ASIC Init begin

  770. LoadZspCode Success, waiting for bootting…

  771. HIAPI_ZspBootCompleteWait: Boot Complete!

  772. ASIC Init end

  773. Init DSP OK!

  774. Slic init Start…

  775. Slic init success…

  776. HW_VSPA_InitUnionCheck Result=0x0.

  777. hw_msg_send.c:<46>:Try to start launch oam by message!

  778. VSPA Init Complete!

  780. [Start Phase]::uiStartPhase: 8, uiEndPhase: 9, Seconds: 11

  781. HW_Init_Frame bbsp Successful.

  782. InitFrame get next state ssmp; PID=539; state=9; Sec=45;

  783. InitFrame get next state vspa_sip; PID=557; state=9; Sec=45;

  785. [Start Phase]::uiStartPhase: 9, uiEndPhase: 10, Seconds: 0

  786. InitFrame get next state ssmp; PID=539; state=10; Sec=45;

  787. InitFrame get next state vspa_sip; PID=557; state=10; Sec=45;

  789. [Start Phase]::uiStartPhase: 10, uiEndPhase: 11, Seconds: 0

  791. [Start Phase]::uiStartPhase: 0, uiEndPhase: 11, Seconds: 33

  792. HW_Init_Frame ssp success

  793. HW_Init_Frame VSPA Successful.

  794. VSPA pri restore! Now:0

  795. Systerm start uiPhase:11 enCfgFlag:0!

  796. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  797. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  798. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.3.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  799. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.4.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  800. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.5.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  801. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.6.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  802. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.7.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  803. [hw_xml_dbmain.c]:[4085]Not Find in Ctree:CPath=InternetGatewayDeviceConfig.InternetGatewayDevice.WANDevice.1.WANConnectionDevice.8.WANIPConnection.1.X_HW_ExtendDHCPOPTION60.1

  804. Dropped the page cache.

  805. HW_DIA_InitHmem success;

  806. HW_Shell_InitFuncReg.uiReturn=0x00000000;

  807. ETHOAM Init Lsw lib Tbl Successfully!

  809. ethoam upport mode =1

  810. HW_ETHOAM_InitCbbPubIf succeed!

  811. HW_ETHOAM_InitCbbDataProcIf succeed!

  812. HW_ETHOAM_Init_CBB_Resource succeed!

  813. <CFM>uiMsgMid = 0x8b

  814. ETHOAM Init SUCCESS.

  815. CFM start!AppName:ethoam

  817. ethoam CFM Used 134 ms

  818. CFM end!AppName:ethoam,uiRet=0x0

  820. Apm set device&business active for VSPA RESET

  821. HW_Init_Frame MU Successful.

  822. vspa_sip Started with WatchProc!

  823. Init Watchdog Start … [WDT] 948: old priority 0, new priority -15

  824. Current upport mode is 0x1;

  825. Valid process name(omci), pid(655)

  826. Valid thread name(GPON_Monitor), pid(655), threadid(658)

  827. Valid thread name(OMCI_PRO_QueryO), pid(655), threadid(674)

  828. Valid thread name(OMCI_PRO_Proces), pid(655), threadid(675)

  829. Valid thread name(OMCI_PRO_SendMa), pid(655), threadid(676)

  830. Valid thread name(OMCI_PRO_RecvMa), pid(655), threadid(677)

  831. Valid thread name(OMCI_STAT_PMMai), pid(655), threadid(678)

  832. Valid thread name(OMCI_CMD_Main), pid(655), threadid(679)

  833. Valid process name(vspa_sip), pid(557)

  835. ===============will kill ethoam process========

  836. ethoam self-kill msg:3

  837. enter to HW_ETHOAM_Uninit

  838. hw_msg_commonproc.c:<169>:process ethoam start flag clean.

  839. Ethoam uninit success

复制代码

请问大神们，这个光猫的启动怎样终止，按Ctrl+C、TPL、123都无效，怎样能刷回来呢？

来源URL：http://www.right.com.cn/forum/thread-132437-1-1.html